Welcome to our Support Portal. Search for answers using the search box below, or create a support ticket if you cannot find your answer.
-
Repairing a Lamp?
-
Product Info
-
-
- Installing Arditi Brand Metal E27 Lampholder's
- How to unlock my ES & SES Lampholder
- Installing Arditi Brand Plastic E27 lampholder's
- How to install our push fit E27 and E14 lampholders
- Wiring an E27 Pull cord Lampholder
- Wiring an E27 Switched Lampholder
- Installing S.Lilley Brand Metal E27 Lampholders
- How to Install our Lampholder Cup and Cord Grip
- Lampholder Bases explained
-
- Wiring A BC Un-Switched Lampholder
- Wiring An S.Lilley BC Switched Lampholder
- Wiring a Plastic BC Lampholder
- Installing the 40mm BC 4 Part Lampholder
- Wiring the BC Push Wire Plastic Snap on Cap Lampholder
- Safer switched lampholder not working
- Aligning a BC Unswitched Lampholder
- Lampholder Bases explained
-
-
- Kit 33 Installation Guide
- Kit 17 Installation Guide - ES Version
- Kit 32 Installation Guide
- Kit 21 Installation Guide
- Ceramic Side Entry Wiring Kit with a ES | E27 | Edison Screw Lampholder
- Ceramic Side Entry Wiring Kit with BC | B22 Lampholder
- Kit 18 Installation Guide
- Kit 15 Installation Guide
- Kit 35 Installation Guide
- Plastic Wooden Table Lamp Fixing Kit With Backplate and Cover - BC Version
- Plastic Wooden Table Lamp Fixing Kit With Wood Nipple – BC Version
- Kit 12 Installation Guide
- Kit 11 Installation Guide
- Kit 8 Installation Guide
- Kit 1 Installation Guide
-
-
Creating a Lamp?
-
- How to fix or install a lampholder onto a ceramic item with limited hand access.
- How to turn a bottle into a light fitting
- Measuring Bottle Hole For Bung Size
- Converting a Hong Kong Paraffin Lamp into a Table lamp
- Installing our ceiling roses
- How to Convert a Gas Blow Torch Into a Light Fitting
- How to repair a light that has a lamp inside and outside
-
-
Videos
Kit 32 Installation Guide
0 out of 5 stars
5 Stars | 0% | |
4 Stars | 0% | |
3 Stars | 0% | |
2 Stars | 0% | |
1 Stars | 0% |
This step by step guide is to aid you in installing our kit 32.
Below is a video on how to install and tighten the bung into your bottle.
- Cap
- Skirt
- Insert (Connection Unit)
- Lock Ring
- Shade Ring
Let’s look at the pieces you get inside the kit and to help you understand what they are called.
1 Step 1
Install the bung as shown in the video above.
The following images are showing the kit being installed onto a wooden lamp base.
1 Step 2
2 Step 3
3 Step 4
Seperate the lampholder into its 5 components, as shown above.
Then take the cap and slide it over the cable, and then screw it onto the bung's thread.
Note: you may need to loosen the lock screw in the bottom of the cap, as shown in the image.
Once the cap has been installed, then tighten that locking screw up inside the lampholder cap, this will lock the lampholder onto the side entry cord grip.
4 Step 5
5 Step 6
6 Step 7
7 Step 8
Once the connection unit is seated, take the skirt and place it over the top.
Then place the lock ring (thicker ring) over and tighten this up, this will lock the skirt onto the cap.
Take note of the indents, these MUST align up, if not the light bulb will not work.
More information on how the align the lampholder can be found here.
0 out of 5 stars
5 Stars | 0% | |
4 Stars | 0% | |
3 Stars | 0% | |
2 Stars | 0% | |
1 Stars | 0% |